IRFA V N-channel A-FET / Substitute of IRF FEATURES. Avalanche Rugged Technology Rugged Gate Oxide Technology Lower Input Capacitance. THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT ? IRFA datasheet, IRFA pdf, IRFA data sheet, datasheet, data sheet, pdf , Fairchild Semiconductor, N-CHANNEL POWER MOSFET.

Author: Kazragor Ket
Country: Guatemala
Language: English (Spanish)
Genre: Photos
Published (Last): 10 May 2015
Pages: 417
PDF File Size: 9.71 Mb
ePub File Size: 3.7 Mb
ISBN: 671-7-32557-240-3
Downloads: 45836
Price: Free* [*Free Regsitration Required]
Uploader: Mikalrajas

And a step up boost converter to supply the 5. If it would be just a wire i.

Can i use this circuit with Arduino to drive 2 x 20W 1. If you are using this circuit to switch any serious loads, then it is wise to solder some thick wire over the tracks coming from the MOSFET. Notify me of dqtasheet comments via email. Leave a Reply Cancel reply Enter your comment here Or am I overlooking something?

I am not sure where you are based but the IRL costs abt 60 cts where I am. Perhaps one of the wires is corrupt. Thanks very much for your time.


Realise though that it is an inverting circuit. You are commenting using your Twitter account. Every time I tried with new IRF, but any of them worked only for first time. Do you have any idea why is the mosfet not working properly and letting the 12v works on the led strip? The Vce in saturation is about 0. Is it for audio?


IRF530A MOSFET. Datasheet pdf. Equivalent

Sometimes a MCU seems to be driving a mosfet correctly, but only a careful measurement will show the mosfet is not getting fully turned on, overheating and wasting power. Setting a temperature to a comfortable level arduino switches the mosfet on for sec followed by a 50sec off time.

You are commenting using your Facebook account. The 2n datasheeet, often used with the arduino is even worse in that aspect, but if used daatsheet switch an LED it is OK rdsOn about ohms at 4.

IRFA 데이터시트(PDF) – Fairchild Semiconductor

A logic level mosfet means that it is designed to turn on fully from the logic level of a microprocessor. To find out more, including how to control cookies, see here: They are good switches,but you dont want to use datasneet as resistors.

At 8A it is not even breaking a sweat.

Here is the curve for the IRL If you feed it with 15Volt the output voltage is around volt which will do the job. I am getting almost 7V at the gate so no issues. These transistors will invert the signal from the N-channel mosfet, ensuring no short circuits could happen.

PDF IRF530A Datasheet ( Hoja de datos )

Anyway, depending on your circuit, I am not sure if you need a logic level P fet as often there is transistor driving datadheet mosfet. Joe, good idea, but as I picture your changes, the emittor datadheet be at 12 Volt when open, while yr Arduino will set the basis at a max of 5Volt, which would cause the transistor to close again. But suppose the FET you choose has 0.


Sadly though it can ir5f30a dissipate some 80 Watts There is the MTB60N05HD L that does 60 amps 50 Volt and Amps beware of the somewhat high input capacutance, bu thta does not need to be a huge problem in simple switching also you may consider browsing through this guide.

Checking the datasheet is always a good suggestion.

True is that car heated seat is not a very demanding load when properly controlled. Datasheft luck with your project. I just need to switch on and off small DC motor. Good luck, but dont daatasheet to ask again shld you need further advice.

I bought it and it works with Arduino. That 52 mOhms at 2. The question is the one joe provided a solution to in an earlier question, except just as you pointed out, his solution doesnt work because the emitter voltage will be close to 12V and the base voltage from the arduino will be 5V so the transistor will close.